Chevrolet Trax Owners & Service Manuals

Chevrolet Trax: Battery disconnect warning

WARNING: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

For Vehicles equipped with OnStar (UE1) with Back Up Battery: The Back Up Battery is a redundant power supply to allow limited OnStar functionality in the event of a main vehicle battery power disruption to the VCIM (OnStarmodule). Do not disconnect the main vehicle battery or remove the OnStar fuse with the ignition key in any position other than OFF. Retained accessory power should be allowed to time out or be disabled (simply opening the driver door should disable retained accessory power) before disconnecting power. Disconnecting power to the OnStar module in any way while the ignition is On or with retained accessory power activated may cause activation of the OnStar Back-Up Battery system and will discharge and permanently damage the back-up battery. Once the Back-Up Battery is activated it will stay on until it has completely discharged. The back-up battery is not rechargeable and once activated the back-up battery must be replaced.

BRAKE DUST WARNING

WARNING: Avoid taking the following actions when you service wheel brake parts:

  • Do not grind brake linings.
  • Do not sand brake linings.
  • Do not clean wheel brake parts with a dry brush or with compressed air.

Some models or aftermarket brake parts may contain asbestos fibers which can become airborne in dust. Breathing dust with asbestos fibers may cause serious bodily harm. Use a water-dampened cloth in order to remove any dust on brake parts. Equipment is available commercially in order to perform this washing function. These wet methods prevent fibers from becoming airborne.

BRAKE FLUID IRRITANT WARNING

WARNING: Brake fluid may irritate eyes and skin. In case of contact, take the following actions:

  • Eye contact-rinse thoroughly with water.
  • Skin contact-wash with soap and water.
  • If ingested-consult a physician immediately.

BRAKE FLUID WARNING

WARNING: Use only Delco Supreme 11, GM P/N 12377967 (Canadian P/N 992667), or equivalent DOT 3 brake fluid from a clean, sealed container. Do not use fluid from an open container that may be contaminated with water.

Improper or contaminated fluid could result in damage to components, or loss of braking, with possible injury.

    READ NEXT:

     Checking hot transmission fluid through drain plug hole warning

    WARNING: The engine must be running when the transmission fluid fill plug is removed, or excessive fluid loss will occur. Transmission fluid may be hot. Since the actual fluid level is unknown, stand

     Parking brake and drive wheels warning

    WARNING: Apply the parking brake and block the drive wheels before performing this procedure in order to prevent bodily injury. PROTECTIVE GOGGLES AND GLOVE WARNING WARNING: Always wear protective go

     Sir seatbelt pretensioner handling warning

    WARNING: When carrying an undeployed inflatable restraint seat belt retractor pretensioner: Do not carry the seat belt pretensioner by the seat belt webbing or pigtail connector, if equipped. C

    SEE MORE:

     Immobilizer - Repair instructions

    THEFT DETERRENT MODULE REPLACEMENT (ENCORE) Fig. 3: Theft Deterrent Module (Encore) Theft Deterrent Module Replacement (Encore) THEFT DETERRENT MODULE REPLACEMENT (TRAX) Fig. 4: Theft Deterrent Module Theft Deterrent Module Replacement (Trax) IMMOBILIZER SYSTEM COMPONENT PROGRAMMING This pro

     Brake pressure modulator valve bracket replacement

    Removal Procedure Remove the brake pressure modulator valve (BPMV) and bracket assembly. Refer to Brake Pressure Modulator Valve Replacement. Fig. 24: Brake Pressure Modulator Valve Bolts Remove the BPMV bolts (1). Remove the BPMV bracket. Installation Procedure Install the BPMV bracket

    © 2019-2024 Copyright www.chevtrax.com