Chevrolet Trax: Power steering hose disconnected caution

CAUTION: Do not start the vehicle with any power steering gear inlet or outlet hoses disconnected. When disconnected, plug or cap all openings of components. Failure to do so could result in contamination or loss of power steering fluid and damage to the system.

REFRIGERANT PRESSURE DURING TESTING CAUTION

CAUTION: Leak detection shall only be done with the refrigerant that is specified for the system. Do not attempt to increase pressure of the A/C refrigerant system with shop air or another type of refrigerant. Failure to follow the above guidelines could result in damage to the vehicle or its components.

SILICON CONTAMINATION OF HEATED OXYGEN SENSORS CAUTION

CAUTION: Contamination of the oxygen sensor can result from the use of an inappropriate RTV sealant (not oxygen sensor safe) or excessive engine coolant or oil consumption. Remove the HO2S and visually inspect the portion of the sensor exposed to the exhaust stream in order to check for contamination. If contaminated, the portion of the sensor exposed to the exhaust stream will have a white powdery coating. Silicon contamination causes a high but false HO2S signal voltage (rich exhaust indication). The control module will then reduce the amount of fuel delivered to the engine, causing a severe driveability problem. Eliminate the source of contamination before replacing the oxygen sensor.

STEERING COLUMN IN LOCK POSITION CAUTION

CAUTION: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column lock, or a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:

• The steering column
• The steering shaft coupling
• The intermediate shaft(s)

After disconnecting these components, do not rotate the steering wheel or move the front tires and wheels. Failure to follow this procedure may cause the SIR coil assembly to become un-centered and cause possible damage to the SIR coil. If you think the SIR coil has became un-centered, refer to your specific SIR coil's centering procedure to re-center SIR Coil.

STEERING WHEEL IN THE FULL TURN POSITION CAUTION

CAUTION: Do not hold the steering wheel in the full turn position longer than 5 seconds, as damage to the steering pump may result.

STEERING WHEEL STRAIGHT AND COLUMN LOCKED CAUTION

CAUTION: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column lock, or a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:

• The steering column
• The intermediate shaft(s)
• The steering gear

After disconnecting these components, do not rotate the steering wheel or move the front tires and wheels. Failure to follow this procedure may cause the SIR coil assembly to become un-centered and cause possible damage to the SIR coil. If you think the SIR coil has became un-centered, refer to your specific SIR coil's centering procedure to re-center SIR Coil.

TAPE CORNERS OF PANEL CAUTION

CAUTION: When removing body panels, apply tape to corners of panel and adjacent surfaces to help prevent paint damage.

TEST PROBE CAUTION

CAUTION: Do not insert test equipment probes (DMM etc.) into any connector or fuse block terminal. The diameter of the test probes will deform most terminals.

A deformed terminal will cause a poor connection, which will result in a system failure. Always use the J-35616-F GM Approved Terminal Release Tool Kit in order to front probe terminals. Do not use paper clips or other substitutes to probe terminals. When using the J-35616-F GM Approved Terminal Release Tool Kit , ensure the terminal test adapter choice is the correct size for the connector terminal. Do not visually choose the terminal test adapter because some connector terminal cavities may appear larger than the actual terminal in the cavity. Using a larger terminal test adapter will damage the terminal. Refer to the J-35616-F GM Approved Terminal Release Tool Kit label on the inside of the J-35616-F GM Approved Terminal Release Tool Kit for the correct adapter along with the connector end view for terminal size.

TORQUE-TO-YIELD FASTENER CAUTION

CAUTION: This vehicle is equipped with torque-to-yield or single use fasteners.

Install a NEW torque-to-yield or single use fastener when installing this component. Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.

USING PROPER POWER STEERING FLUID CAUTION

CAUTION: When adding fluid or making a complete fluid change, always use the proper power steering fluid. Failure to use the proper fluid will cause hose and seal damage and fluid leaks.

VEHICLE LIFTING AND JACKING CAUTION

CAUTION: Perform the following steps before beginning any vehicle lifting or jacking procedure:

• Remove or secure all of the vehicle contents in order to avoid any shifting or any movement that may occur during the vehicle lifting or jacking procedure.
• The lifting equipment or the jacking equipment weight rating must meet or exceed the weight of the vehicle and any vehicle contents.
• The lifting equipment or the jacking equipment must meet the operational standards of the lifting equipment or jacking equipment manufacturer.
• Perform the vehicle lifting or jacking procedure on a clean, hard, dry, level surface.
• Perform the vehicle lifting or jacking procedure only at the identified lift points. DO NOT allow the lifting equipment or jacking equipment to contact any other vehicle components.

Failure to perform the previous steps could result in damage to the lifting equipment or the jacking equipment, the vehicle, and/or the vehicle contents.

WINDSHIELD INSTALLATION CAUTION

CAUTION: Do not use spacers when installing a windshield. The stress caused by the spacers may damage the windshield.

READ NEXT: