Chevrolet Trax Owners & Service Manuals

Chevrolet Trax: DTC C0277: Brake pedal position sensor circuit calibration not learned

Chevrolet Trax (2013-2022) Workshop Manual / Brakes / Antilock Brake System / Diagnostic information and procedures / DTC C0277: Brake pedal position sensor circuit calibration not learned

Diagnostic Instructions

  • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
  • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
  • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC C0277 4B

Brake Pedal Position Sensor Circuit Calibration Not Learned

Circuit/System Description

When the brake pedal is applied, the body control module sends a serial data message to the electronic brake control module in reference to the brake pedal positions. The electronic brake control module compares the correlation between the brake pedal position and the amount of brake pressure it senses from the brake pressure sensor, which is internal to the brake pressure modulator. It uses this information to control the vehicle during an stability control event

Conditions for Running the DTC

  • Brakes Applied.
  • Battery voltage must be between 9-16 V.

Conditions for Setting the DTC

  • The body control module sends invalid brake pedal position data to the electronic brake control module.
  • The DTC may set in the body control module and/or electronic brake control module, when the brake pedal position sensor home position is not learned.

Actions Taken When the DTC Sets

  • The ABS indicator is commanded ON.
  • The red brake indicator is commanded ON.
  • The stop lamps may not activate at the expected brake pedal positions.
  • The traction/stability control indicator turns ON, if equipped with electronic stability control.

Conditions for Clearing the DTC

  • The condition responsible for setting the DTC no longer exists.
  • A DTC will not clear the current status until the next ignition cycle.
  • A successful brake pedal position sensor calibration has been performed.
  • A history DTC will clear once 40 malfunction-free ignition cycles have occurred

Reference Information

Schematic Reference

  • Antilock Brake System Schematics(Encore), Antilock Brake System Schematics (Trax)
  • Exterior Lights Schematics (Encore) , Exterior Lights Schematics (Trax)

Connector End View Reference

WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - INDEX - ENCORE WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - INDEX - (Trax)

Description and Operation

  • ABS Description and Operation
  • Exterior Lighting Systems Description and Operation

Electrical Information Reference

  • Circuit Testing
  • Connector Repairs
  • Testing for Intermittent Conditions and Poor Connections
  • Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Verify DTC C0277 is not set in the K9 Body Control Module

If DTC is set

Refer to DTC C0277 or C0890 .

If DTC is not set

  1. Ignition ON
  2. Verify the scan tool Body Control Module Brake Pedal Position Sensor Learned Released Position is YES.

If the released position is not YES

Perform the Brake Pedal Position Sensor Learn. Refer to Brake Pedal Position Sensor Calibration .

If the released position is YES

  1. Verify the DTC does not set while operating the vehicle within the Conditions for Running the DTC.

If the DTC sets

Replace the K17 Electronic Brake Control Module.

If the DTC does not set

  1. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for Electronic Brake Control Module replacement, programming and setup

    READ NEXT:

     DTC C027C: Front brake discs high temperature

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC C0292: Multi-axis acceleration sensor module circuit performance - bias level out of range

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC C0551: Multi-axis acceleration sensor module circuit erformance - bias level out of rangee

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

    SEE MORE:

     Rear wheel drive shaft replacement

    Special Tools CH-45859 Axle Remover For regional equivalent tools, refer to Special Tools. Removal Procedure Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation . Fig. 30: Removing St

     DTC B3715 OR B3875: Windshield wiper relay

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category DTC Descriptors DT

    © 2019-2024 Copyright www.chevtrax.com