Chevrolet Trax: DTC B370A: Rain sensor
DIAGNOSTIC CODE INDEX
DIAGNOSTIC CODE INDEX
DTC B370A: RAIN SENSOR
Diagnostic Instructions
- Perform the Diagnostic System Check - Vehicle prior to using this
diagnostic procedure.
- Review Strategy Based Diagnosis for an overview of the diagnostic
approach.
- Diagnostic Procedure Instructions provides an overview of each
diagnostic category.
DTC Descriptor
DTC B370A
Rain Sensor
For symptom byte information, refer to Symptom Byte List .
Circuit/System Description
B+ and ground is supplied at all times to the rain sensor. The rain sensor
communicates with the body control
module (BCM) via serial data. When the ignition is in the ON or ACCESSORY
position and the windshield
wiper/washer switch is in the intermittent delay position, the BCM monitors the
rain sensor to determine the
rain build up on the windshield. As rain builds up on the windshield, the BCM
will command the wipers to
activate. The sensitivity of the wiper frequency is controlled by the
intermittent delay of the windshield
wiper/washer switch. As the sensitivity is increased, the BCM will command more
frequent wiper activation
based on rain build up on the windshield.
Conditions for Running the DTC
- Ignition ON.
- The system voltage is between 9-16 V.
Conditions for Setting the DTC
Communication between the BCM and the rain sensor is interrupted.
Action Taken When the DTC Sets
- If the BCM loses communication with the rain sensor while operating with
single wipes, the windshield
wiper operation will default to intermittent operation with a fixed dwell
time of 4 seconds.
- If the BCM loses communication with the rain sensor while operating at
low speed, the windshield wiper
operation will default to low speed.
- If the BCM loses communication with the rain sensor while operating at
high speed, the windshield wiper operation will default
to high speed.
Conditions for Clearing the DTC
The DTC will clear when communication is established between the BCM and rain
sensor.
Reference Information
Schematic Reference
Wiper/Washer Schematics (Encore), Wiper/Washer Schematics (Trax)
Connector End View Reference
WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS -
INDEX - ENCORE WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT
CONNECTOR END VIEWS - INDEX - TRAX
Description and Operation
Wiper/Washer System Description and Operation
Electrical Information Reference
- Circuit Testing
- Connector Repairs
- Testing for Intermittent Conditions and Poor Connections
- Wiring Repairs
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Ignition ON.
- Verify DTC U151A is not set.
If the DTC is set
Please Refer to DTC U1500-U15FF
If the DTC is not set
- Verify the windshield wipers operate at low speed when the S82
Windshield Wiper/Washer Switch is in
the LO position.
- If the windshield wipers are not operating at low speed
Refer to Windshield Wiper System Malfunction.
- If the windshield wipers are operating at low speed
- Place the S82 Windshield Wiper/Washer Switch in the intermittent delay
setting and spray the outside of
the windshield in the area of the B117 Rain Sensor with a water bottle. It
may be necessary to increase
the sensitivity of the intermittent delay to achieve windshield wiper
operation.
- Verify the windshield wipers operate at low speed.
- If the wipers are not operating at low speed
Test or replace the B117 Rain Sensor.
- If the wipers are operating at low speed
- All OK.
Repair Instructions
Perform the Diagnostic Repair Verification after completing the repair.
Windshield Outside Moisture Sensor Replacement
READ NEXT:
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this
diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic
approach.
Diag
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this
diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic
approach.
Diag
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this
diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic
approach.
Diag
SEE MORE:
Window Motor Normalized Procedure
A window motor that has not been normalized will no longer perform the
express up and express down
functions, this may occur during the following conditions:
When a window motor has been disconnected or replaced
When a door harness has been disconnected
When th
Rain and wet roads can reduce
vehicle traction and affect your
ability to stop and accelerate.
Always drive slower in these types
of driving conditions and avoid
driving through large puddles and
deep‐standing or flowing water.
Warning
Wet brakes can cause crashes.
They might not work as well in