Chevrolet Trax Owners & Service Manuals

Chevrolet Trax: DTC B3031: Security controller in learn mode

Diagnostic Instructions

  • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
  • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
  • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B3031

Security Controller In Learn Mode

For symptom byte information, refer to Symptom Byte List .

Circuit/System Description

When learning a coded key, the body control module (BCM) is placed in learn mode. DTC B3031 will set automatically as an indicator that the system is in learn mode and not as a fault indicator. Once the coded key is learned, learn mode will be exited and the DTC cleared. If the BCM does not exit learn mode, DTC B3031 will remain current and indicate a fault. The instrument cluster security indicator will illuminate and the driver information center will display a message.

Conditions for Running the DTC

The immobilizer system is the learn coded keys state.

Conditions for Setting the DTC

The DTC will set any time the BCM enters the learn coded keys state.

Action Taken When the DTC Sets

The security indicator will illuminate. The driver information center will display a message.

Conditions for Clearing the DTC

  • A current DTC B3031 will be cleared upon the successful exit of learn mode.
  • A history DTC will be cleared after 100 malfunction-free ignition cycles.

Reference Information

Schematic Reference

Immobilizer Schematics (Encore), Immobilizer Schematics (Trax)

Connector End View Reference

WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - INDEX - ENCORE WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - INDEX - TRAX

Description and Operation

Immobilizer Description and Operation

Electrical Information Reference

  • Circuit Testing
  • Connector Repairs
  • Testing for Intermittent Conditions and Poor Connections
  • Wiring Repairs

Scan Tool Reference

  • Control Module References for scan tool information
  • Circuit/System Verification
  1. Verify all available keys are correct for the vehicle. This can be accomplished by comparing the part number that is laser etched on the key to the part number listed in the parts catalog.
  • If a key is not correct

Replace the key

  • If all keys are correct
  1. Perform the Replacing Keys procedure. Refer to Key with Integrated Transmitter Programming.
  2. Verify the K9 Body Control Module learns the vehicle key and exits the learn coded key state. The scan tool Master Keys Learned parameter should increment to 1.
  • If the K9 Body Control Module does not exit the learn coded key state after the programming attempt

Replace the K9 Body Control Module

  • If the K9 Body Control Module exits the learn coded key state after the programming attempt
  1. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for body control module replacement, programming, and setup.

    READ NEXT:

     DTC B3055: Security controller in learn mode

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC B305C: Immobilizer transponder of wrong type programmed

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC B3060: Unprogrammed transponder identification code received

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

    SEE MORE:

     Symptoms - automatic transmission shift lock control

    IMPORTANT: The following steps must be completed before using the symptom tables. Perform the Diagnostic System Check - Vehicle before using the Symptom Tables in order to verify that all of the following are true: There are no DTCs set. The control modules can communicate via the serial d

     Front wheel drive shaft replacement - right side

    Special Tools J 45859 Hub Spindle Remover Fro regional special tools, refer to Special Tools. Removal Procedure Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation . Fig. 17: Front Su

    © 2019-2024 Copyright www.chevtrax.com