Chevrolet Trax Owners & Service Manuals

Chevrolet Trax: DTC B0052: Deployment commanded

Diagnostic Instructions

  • Perform the Diagnostic System Check - Vehicle prior to using the diagnostic procedure.
  • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
  • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0052 00

Deployment Commanded

DTC B0052 56

Deployment Commanded Too Many Transitions

Circuit/System Description

The inflatable restraint sensing and diagnostic module (SDM) senses vehicle impacts and provides deployment signals to the air bags and anchor and/or retractor pretensioners when warranted. The inflatable restraint sensing and diagnostic module sets DTC B0052 after each command for deployment. DTC B0052 will latch and not clear after 3 commanded deployments by the inflatable restraint sensing and diagnostic module. Therefore the inflatable restraint sensing and diagnostic module has to be replaced.

Conditions for Running the DTC

Ignition voltage is between 9-16 V.

Conditions for Setting the DTC

  • The inflatable restraint sensing and diagnostic module detects a frontal impact of sufficient force to warrant deployment of the frontal air bags.
  • The inflatable restraint sensing and diagnostic module detects a side impact or rollover (if equipped) of sufficient force to warrant deployment of a seat air bag and/or roof rail air bag.

Action Taken When the DTC Sets

The inflatable restraint sensing and diagnostic module requests the instrument cluster to illuminate the AIR BAG indicator.

Conditions for Clearing the DTC

  • DTC B0052 00 is a DTC that may be cleared with a scan tool without replacing the inflatable restraint sensing and diagnostic module. This DTC will not clear if deployment has been commanded more then two times, and the inflatable restraint sensing and diagnostic module would have to be replaced.
  • DTC B0052 56 is a latched DTC. The DTC cannot be cleared with the scan tool. Replacement of the inflatable restraint sensing and diagnostic module is required.

Reference Information

Schematic Reference

SIR Schematics (Encore), SIR Schematics (Trax)

Connector End View Reference

WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - INDEX - ENCORE WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - INDEX - TRAX

Description and Operation

Supplemental Inflatable Restraint System Description and Operation

Electrical Information Reference

  • Circuit Testing
  • Testing for Intermittent Conditions and Poor Connections
  • Wiring Repairs
  • Connector Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Verify that DTC B0052 00 is not set.
  • If DTC B0052 00 is set

Clear the DTC. If the DTC will not clear, replace the K36 Inflatable Restraint Sensing and Diagnostic Module.

  • If DTC B0052 00 is not set
  1. Verify that DTC B0052 56 is not set.
  • If DTC B0052 56 is set

Replace the K36 Inflatable Restraint Sensing and Diagnostic Module.

  • If DTC B0052 56 is not set
  1. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for inflatable restraint sensing and diagnostic module replacement, programming and setup

    READ NEXT:

     DTC B0074: Passenger presence sensor

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC B0081 (Inflatable restraint sensing and diagnostic module): passenger presence module

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC B0081: Passenger presence module

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

    SEE MORE:

     Automatic transmission range selector lever replacement

    Removal Procedure Set the park brake and chock the wheels. Fig. 4: Automatic Transmission Range Selector Lever Cable Terminal And Shift Lever Pin Disconnect the transmission range selector lever cable terminal (1) from the transmission manual shift lever pin. Press the locking tabs inwar

     Front brake caliper bracket replacement

    Removal Procedure WARNING: Refer to Brake Dust Warning . Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation . Fig. 38: Upper And Lower Brake Caliper Guide Pin Bolts NOTE: DO NOT us

    © 2019-2024 Copyright www.chevtrax.com