Chevrolet Trax Owners & Service Manuals

Chevrolet Trax: Electronic brake control module programming and setup

Chevrolet Trax (2013-2022) Workshop Manual / General Information & Maintenance / Programming and Setup - All ASystems / Electronic brake control module programming and setup

NOTE:

  • DO NOT program a control module unless directed to by a service procedure or a service bulletin. If the control module is not properly configured with the correct calibration software, the control module will not control all of the vehicle features properly.
  • Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector. If there is an interruption during programming, programming failure or control module damage may occur.
  • Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. When required install the EL-49642 SPS Programming Support Tool to maintain system voltage. If not available, connect a fully charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT connect a battery charger.
  • Turn OFF or disable systems that may put a load on the vehicles battery such as; interior lights, exterior lights (including daytime running lights), HVAC, radio, etc.
  • During the programming procedure, follow the SPS prompts for the correct ignition switch position.

    Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M) system status indicators to NO.

Reference Information

Special Tools

EL-49642 SPS Programming Support Tool

Replace and Program Control Module or Reprogram Control Module

To program a replacement or an existing control module, perform the following procedure:

  1. Install EL-49642 SPS Programming Support Tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3.  On the SPS Supported Controllers screen, select K17 Electronic Brake Control Module - Programming and follow the on-screen instructions.
  4. On the SPS Supported Controllers screen, select K17 Electronic Brake Control Module - Configuration and Setup while following the on-screen instructions.
  5. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

Unsuccessful Programming Recovery

In the event of an interrupted or unsuccessful programming event, perform the following steps:

  1. Ignition ON. Ensure the control module, DLC and programming tool connections are secure and the SPS software is up to date.
  2. Verify the control module can be reprogrammed.
  • If the control module cannot be reprogrammed
  1. Ignition OFF for one minute, ignition ON.
  2. Verify the control module can be reprogrammed.
  • If the control module cannot be reprogrammed, replace the control module.
  • If the control module can be reprogrammed
  1. All OK.
  • If the control module can be reprogrammed
  1. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for Control Module replacement, programming and setup

K20 ENGINE CONTROL MODULE: PROGRAMMING AND SETUP

Special Tools

EL-49642 SPS Programming Support Tool

For equivalent regional tools, refer to Special Tools.

NOTE:

  • DO NOT program a control module unless directed to by a service procedure or a service bulletin. If the control module is not properly configured with the correct calibration software, the control module will not control all of the vehicle features properly.
  • Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector. If there is an interruption during programming, programming failure or control module damage may occur.
  • Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. When required install the EL-49642 SPS Programming Support Tool to maintain system voltage. If not available, connect a fully charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT connect a battery charger.
  • Turn OFF or disable systems that may put a load on the vehicles battery such as; interior lights, exterior lights (including daytime running lights), HVAC, radio, etc.
  • During the programming procedure, follow the SPS prompts for the correct ignition switch position.
  • Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M) system status indicators to NO.

    Note the engine oil life remaining percentage.

Replace and Program Control Module

To program a replacement K20 Engine Control Module (ECM), perform the following procedure:

  1. Install EL-49642 SPS programming support tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. Before removing the old control module, perform the SPS function Prepare Control Module for Removal, if available.

NOTE: The Prepare Control Module for Removal function can only be performed when communication with the old control module is still possible.

  1. Replace the ECM.
  2. Perform the SPS function K20 Engine Control Module - Programming and follow the on-screen instructions.
  3. Clear the DTCs after completing the Programming procedure.
  4. Perform the SPS function Immobilizer Learn and follow the on-screen instructions. Refer to Immobilizer System Component Programming .
  5. Perform the SPS function K20 Engine Control Module - Configuration & Setup and follow the on-screen instructions.
  6. Clear DTCs after completing the Configuration & Setup procedure.

Reprogram Control Module

To reprogram an existing K20 Engine Control Module, perform the following procedure:

  1. Install EL-49642 SPS programming support tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. Clear DTCs after completing the Programming procedure.

NOTE: If vehicle fails to start during Configuration and Setup, perform the SPS Function Immobilizer Learn and follow the on-screen instructions.

  1. Perform the SPS function Engine Control Module - Configuration & Setup and follow the on-screen instructions, if available.
  2. Clear DTCs after completing the Configuration & Setup procedure.

Unsuccessful Programming Recovery

In the event of an interrupted or unsuccessful programming event, perform the following:

  1. Ignition ON. Ensure the control module, DLC, and programming tool connections are secure and the SPS software is up to date.
  2. Verify the control module can be reprogrammed
  • If the control module cannot be reprogrammed
  1. Ignition OFF for one minute, ignition ON.
  2. Verify the control module can be reprogrammed.
  • If the control module cannot be reprogrammed, replace the K20 Engine Control Module.
  • If the control module can be reprogrammed
  1. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for ECM replacement, programming and setup.

    READ NEXT:

     Front view camera module programming and setup

    Front View Camera Module Replacement If the Front View Camera Module needs to be replaced, the following procedures must be performed: Connect a scan tool to the vehicle and access Service Programm

     Inflatable restraint sensing and diagnostic module programming and Setup

    The inflatable restraint sensing and diagnostic module (SDM) must be programmed with the proper calibration software. The module stores and utilizes this information however if it is not properly co

     Object alarm module programming and setup

    NOTE: DO NOT program a control module unless directed to by a service procedure or a service bulletin. If the control module is not properly configured with the correct calibration software, the c

    SEE MORE:

     How to Add Coolant to the Coolant Surge Tank

    Caution This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged. If no problem is found, check to see if coolant is visible in the coolant surge tank. If coolant is visible but the coolant level is not at the ind

     Body lock pillar upper trim panel replacement

    Fig. 28: Body Lock Pillar Upper Trim Panel Body Lock Pillar Upper Trim Panel Replacement QUARTER LOWER REAR TRIM PANEL REPLACEMENT Fig. 29: Quarter Lower Rear Trim Panel Quarter Lower Rear Trim Panel Replacement QUARTER STOWAGE POCKET DOOR REPLACEMENT (LEFT SIDE) Fig. 30: Quarter Stowage

    © 2019-2024 Copyright www.chevtrax.com