Chevrolet Trax: Cleaning procedures
NOTE: Examples used in this article are general in nature and do not necessarily relate to a specific engine or system. Illustrations and procedures have been chosen to guide mechanic through engine overhaul process. Descriptions of processes of cleaning, inspection, assembly and machine shop practice are included.
Always refer to appropriate engine overhaul article, if available, in the ENGINES section for complete overhaul procedures and specifications for the vehicle being repaired.
GENERAL
NOTE: Examples used in this article are general in nature and do not necessarily relate to a specific engine or system. Illustrations and procedures have been chosen to guide mechanic through engine overhaul process. Descriptions of processes of cleaning, inspection, assembly and machine shop practice are included.
Always refer to appropriate engine overhaul article, if available, in the ENGINES section for complete overhaul procedures and specifications for the vehicle being repaired.
All components of an engine do not have the same cleaning requirements. Physical methods include bead blasting and manual removal. Chemical methods include solvent blast, solvent tank, hot tank, cold tank and steam cleaning of components.
BEAD BLASTING
NOTE: Examples used in this article are general in nature and do not necessarily relate to a specific engine or system. Illustrations and procedures have been chosen to guide mechanic through engine overhaul process. Descriptions of processes of cleaning, inspection, assembly and machine shop practice are included.
Always refer to appropriate engine overhaul article, if available, in the ENGINES section for complete overhaul procedures and specifications for the vehicle being repaired.
Manual removal of deposits may be required prior to bead blasting, followed by some other cleaning method.
Carbon, paint and rust may be removed using bead blasting method. Components must be free of oil and grease prior to bead blasting. Beads will stick to grease or oil soaked areas causing area not to be cleaned.
Use air pressure to remove all trapped residual beads from component after cleaning. After cleaning internal engine parts made of aluminum, wash thoroughly with hot soapy water. Component must be thoroughly cleaned as glass beads will enter engine oil resulting in bearing damage.
CHEMICAL CLEANING
NOTE: Examples used in this article are general in nature and do not necessarily relate to a specific engine or system. Illustrations and procedures have been chosen to guide mechanic through engine overhaul process. Descriptions of processes of cleaning, inspection, assembly and machine shop practice are included.
Always refer to appropriate engine overhaul article, if available, in the ENGINES section for complete overhaul procedures and specifications for the vehicle being repaired.
Solvent tank is used for cleaning oily residue from components. Solvent blasting sprays solvent through a siphon gun using compressed air.
The hot tank, using heated caustic solvents, is used for cleaning ferrous materials only. DO NOT clean aluminum parts such as cylinder heads, bearings or other soft metals using the hot tank. After cleaning, flush parts with hot water.
A non-ferrous part will be ruined and caustic solution will be diluted if placed in the hot tank. Always use eye protection and gloves when using the hot tank.
Use of a cold tank is for cleaning aluminum cylinder heads, carburetors and other soft metals. A less caustic and unheated solution is used. Parts may be left in the tank for several hours without damage. After cleaning, flush parts with hot water.
Steam cleaning, with boiling hot water sprayed at high pressure, is recommended as the final cleaning process when using either hot or cold tank cleaning.
READ NEXT:
Component cleaning
NOTE: Examples used in this article are general in nature and do
not necessarily relate
to a specific engine or system. Illustrations and procedures have been chosen
to guide mechanic through engine
Cylinder head replacement
NOTE: Examples used in this article are general in nature
and do not necessarily relate
to a specific engine or system. Illustrations and procedures have been chosen
to guide mechanic through engine
Cylinder head overhaul
NOTE: Examples used in this article are general in nature and do
not necessarily relate
to a specific engine or system. Illustrations and procedures have been chosen
to guide mechanic through engine
SEE MORE:
Sir service precautions
General Service Instructions
WARNING: When performing service on or near the SIR components or
the SIR
wiring, the SIR system must be disabled. Refer to SIR Disabling and
Enabling . Failure to observe the correct procedure could cause
deployment of the SIR components, personal injury, or unnecessar
Vibration theory and terminology
Vibration Theory
The designs and engineering requirements of vehicles have undergone drastic
changes over the last several
years.
Vehicles are stiffer and provide more isolation from road input than they did
previously. The structures of
today's stiffer vehicles are less susceptible to many of th
